With the development of edible fungi production, machinery for the production of edible fungi has also been promoted and used. The following describes the selection and use of several edible fungi machinery for reference.
1. Wood slicer. For forests with many branches and slabs, MG-600 or MG-700 should be used, with 8.82 kW diesel engine or 13 kW electric motor, which can cut wood with a diameter of 15-18 cm, and the productivity is 1500-2000 kg per hour. . When using, first check if the flying knife and connecting bolt are locked. The flying knife needs to sharpen the blade once every 4 hours of operation and correct the edge angle with a 36° square. When cutting, prevent stones, metal and Other debris from entering. When feeding harder and drier wood, add some water to the feeding port to prevent the flying knife from heating and softening. The feed port and the discharge port should not stand in the middle to prevent wood damage.
2. Wood chip crusher. The machine has FS-B, FS-C, FS-D and other models. 100,000 bags of shiitake mushrooms are cultivated. 3000 kilograms of wood chips are processed every day. One FS-D three-screen pulverizer can be used, with a 22 kW electric motor or a 22.05 kW diesel engine. Production of about 300 kg of edible fungi per hour, FS-B type crusher can be used. Usage: (1) Open the upper cover to check whether the hammer is tight, if the bolt is loose, then add enough butter and start the test. (2) Start feeding after the machine is running normally. If abnormal noise occurs, stop the inspection immediately to avoid damage to the machine. (3) When the hammer wear causes a significant drop in productivity, it should be removed and replaced, or replaced with a new hammer. (4) The bag set on the powder outlet is 300 mm in diameter and more than 5 m in length, and the exhaust is better. (5) Feeding must be uniform, do not overload.
3. Culture material bagging machine. This machine is commonly used in A-type mushroom bagging machine and B-type mushroom and white fungus bagging machine. It is equipped with 0.75 kW motor and is suitable for blowing film bags with diameter of 120-170 mm. The productivity is 800-1000 per hour. bag. Usage: (1) Check whether the screws of each part are tight, then turn on the power, and then feed the standby after normal operation. (2) When bagging, one hand gently support the outlet of the sleeve, hold the end of the plastic bag with one hand, and let the plastic bag slowly withdraw while feeding. (3) To use different bags, you need to change the corresponding auger and auger. (4) When the hopper overhead occurs occasionally, the material in the bucket should be dialed in time. Do not put your hand in to avoid rolling injury. (5) If the machine does not discharge, stop it to check if the auger is worn or deformed.
4, sterilization pot. The pot has a variety of specifications, can be loaded with 180-250 bottles, fuel for coal, firewood can be. Usage: (1) The safety valve pressure should be adjusted to about 147.12 kPa for automatic exhaust. (2) Add enough water in the pot before ignition. The flask should be placed in the pot to be stable. The outer flask should be kept at a distance of 110 mm from the lid. (3) Remove the sludge impurities in the rubber ring and the corresponding cover before the pot is closed to prevent air leakage. (4) In the middle of sterilization, it is not possible to stop the fire and cool down, so as to avoid the cotton plug being stained with water. (5) After sterilization, the venting valve should be opened to discharge the gas in the pot. When the pressure in the pot is 47.04-98.08 kPa, close the bleed valve. Open the water valve, drain the water in the pot, and then drain the gas in the pot before opening the lid to take the bottle.
5. Dehydration dryer. The machine has XT-40, XT-60, XT-80 and other models, and can dry mushrooms or fungus 35-80 kg in 18-20 hours. If you cultivate 50,000 bags, you can purchase an XT-40 dehydration dryer. The temperature is controlled during use; the wetted window is fully opened at the beginning of drying, half-open in the middle, and fully closed in the later stage. After drying, first extinguish the fire, then open the drying room to take the product. The soot in the heat exchanger piping should be removed first when continuing to use.
Histone Acetyltransferase Inhibitor
Our Histone Acetyltransferase Inhibitor products is good in quality and competitive in price.
We are manufacturer and supplier of Histone Acetyltransferase Inhibitor products following your specific requirement.
We are looking forward to your E-mail and establishing cooperative relationship with you.
We would provide professional Histone Acetyltransferase Inhibitor products with good services for you.
Histone Acetyltransferase Inhibitor
C646 Inhibitor, Anacardic Acid Inhibitor, Mg149 Inhibitor, Acetyltransferase Inhibitor
Taizhou Crene Biotechnology Co., Ltd. , http://www.crenelab.com